Resources Required
Two '/*" x Γ 18-gauge sterling silver sheet silver Two seven/«" sterling silver bar factors Two five.3 mm x three.two mm 16-gauge sterling silver oval leap rings Two sterling silver ear wires
Resources Required
Ruler
Marker
Jeweler's observed or tin snips Masking tape
Concrete block or landscape paver
Hammer
File
High-quality grit sanding pad Awl
Hard, flat surface /Îί’ drill little bit
Handheld rotary Device, flex shaft, or drill press Liver of sulfur or oxidizing solution High-quality steel wool Polishing fabric
Two pairs of chain nose pliers
1.Use the ruler to evaluate and mark two
rectangle items of eighteen-gauge sterling sheet silver.
2.Using a jeweler's observed or tin snips, Reduce the eighteen-gauge sterling sheet silver into two Vi" x Γ rectangles (if you will end up generating the bracelet and pendant projects, you might want to Reduce all of the rectangle silver items desired for the opposite projects and texture them all at one time).
3.Put the two W x Γ sterling silver rectangle items on to the sticky side of a bit of masking tape. This will allow you to to hold the silver rectangles in position if you are texturing them, and will even assistance to keep your fingertips at a safe distance to stop hitting them Using the hammer.
four.Position the bit of masking tape with the silver rectangles sticky side down onto a concrete block or landscape paver.
5.Using a hammer, Carefully strike the tape-protected silver rectangles employing a firm strike, but Never hit way too really hard. You could achieve the specified texture more easily with numerous gentle strikes instead of several tough strikes. Lift the tape often and check the development with the texturing, ensuring that the whole surface of the silver rectangles is acquiring a uniform texture. The surface area will look comparable to sandpaper Should you be using a concrete block. After you obtain the desired texture, clear away the silver rectangles from your masking tape.
6.the silver rectangles will likely have a slight curve to them, and the edges are going to be misshapen and sharp Once you texture them. You could leave the silver rectangles curved or, to flatten them, position the silver rectangles on a hard, flat surface area and make use of a rawhide mallet men's fashion rings to flatten them. If you don't Possess a rawhide mallet, you can spot the silver rectangles on a tough, flat area, include the items which has a thick piece of scrap leather, and make use of a hammer to gently faucet the leather-based included silver rectangles to rings for men flatten them.
7.You need to make use of a file to do away with any tough or sharp edges. Utilize a fine grit sanding pad to go more than the realm where you have filed to smooth the edges and remove any file marks.
8.Measure from a single stop of men's rings personalized and engraved every textured silver rectangle and spot a mark in the center of each piece. This is where the holes will be drilled to attach the bounce ring and bar factors.
nine.Put on the protection glasses. Place the textured silver rectangles on to a tough, flat surface area. Place The purpose with the awl about the mark which you produced '/t" from the close of your rectangle items and use a hammer to firmly strike at the time on the highest from the awl to help make a pilot hole for drilling the holes into your silver rectangles.
10.Employing a drill bit, drill holes into each on the silver rectangles having a handheld rotary Resource, flex shaft, or drill press. Make sure to put on protection glasses.
11.Utilize the file or sanding pad to get rid of any burs or tough edges remaining from drilling holes in to the silver rectangles.
twelve.Apply liver of sulfur or oxidizing Remedy into the textured silver rectangles, bar components. and leap rings. It is very important to stick to any basic safety tips the manufacturer suggests when working with any chemical compounds.
thirteen.Just after applying the oxidizing Remedy, gents ring use wonderful metal wool to get rid of the darkened spots on the elevated surface area on the silver rectangles, leaving a lot of the textured areas dark. Rub the fantastic steel wool around the bounce rings and bar factors to eliminate some although not most of the darkened parts. Rinse with drinking water, dry, and rub with sharpening cloth.
fourteen.With two set of chain nose pliers pointing up, hold the jump ring with the opening at the top. Roll one of the wrists faraway from you and your other wrist towards you, opening the soar ring only approximately essential. To shut the leap ring, hold it a similar way and roll your wrists in the other direction (think of Keeping a piece of paper and tearing it). Under no circumstances pull the leap ring finishes out as this can weaken the metallic, and it will be tricky to near the soar ring.
15.Insert the bar component and textured silver rectangle gents ring on the bounce ring. Close the soar ring.
sixteen.Gently open up the loop at the bottom of the ear wire, incorporate one other finish with the bar component. after which shut the ear wire loop.
seventeen.Repeat these steps for the next earring.